Multiconductor Feedthroughs For High Temperature Sealing |
| MFT Series |
|
 |
|
|
Multiconductor Feedthroughs For High Temperature Sealing
 |
| Click for larger image. |
|
|
|
|
| • |
Pressure or Vacuum Applications
|
| • |
Seals Multiple Thermocouples
|
| • |
Seals Multiple Protection Tubes
|
| • |
NPT Mounting Thread
|
| • |
Up to 16 Probes in 1 Fitting
|
| • |
Blank Sealing Plugs Included at No Extra Charge
|
| • |
3 to 16 Probes
|
| • |
416SS Body and Cap
|
| • |
316SS Ferrules Standard
|
| • |
PTFE Ferrules Available
|
| • |
Uses Standard OMEGALOK ® Ferrules
|
| • |
.040 Through 1 /4 " Diameter Probes
|
| • |
Blank Sealing Plugs Included at No Extra Charge
|
View related products - Thermocouple Connectors and Panel Systems
|
| |
|
|
|
 |
These all new multiconductor feedthroughs are designed for use in applications that require several sensors to pass through a wall or bulkhead at one opening or within a small area. Heavy duty 416 stainless steel construction allows this fitting to be used in high pressure or vacuum applications. Probes between 0.040" and 0.250" can be used with these feedthoughs. The maximum number of probes per feedthrough is 3 for 1/4" diameter probes, 5 or 3/16" diameter, 8 for 1/8" diameter, 16 for 1/16" diameter and 16 or 0.040" diameter.
All multiconductor feedthroughs are supplied in standard form with stainless steel ferrules. A stainless steel ferrule deforms and becomes permanent. If it is required that the probes be installed several times at different depths in the feedthrough, PTFE ferrules should be used. PTFE ferrules will not deform the probe sheath, allowing the same probe to be reused. The ferrules used in the feedthroughs are identical to the ferrules used in standard OMEGALOK™ compression fittings.
|
|
|
|
|
|
† Price are shown in RMB.
Note: All fittings are supplied with stainless steel ferrules. If PTFE ferrules are required, add suffix "-PTFE" to the model number shown. Add $1 to the cost per PFA ferrule. One ferrule needed for each conductor. PFA tape should be used on all pipe joints to provide a good seal and to prevent the threaded parts from seizing each other on disassembly.
(OPTIONS SHOWN IN THIS "NOTE" ABOVE ARE PRICED IN US$)
|
|
|
|
|
|
|
|
|
Part Number Builder |
|
|
|
|
|
|
|
|
Option Descriptions
|
|
(1)
|
Diameter of Probe in Inches
|
| |
Select
040 for for 0.040 Inch
116 for for 1/16 Inch
18 for for 1/8 Inch
316 for for 3/16 Inch
14 for for 1/4 Inch
|
(2)
|
Number of Probes
|
| |
Select
-3 for for 3 Probes
-5 for for 5 Probes
-6 for for 6 Probes
-8 for for 8 Probes
-10 for for 10 Probes
-12 for for 12 Probes
-16 for for 16 Probes
|
|
NOTE: All combinations may not be valid, check spec sheet for valid part numbers.
|
|
|
|
|
|
|
|
| |
|
Related Links -
Related Products
|
|
|
|
|
|
|
|
